Home  |  About Us  |  Products  |  Services  |  FAQ’s  |  Gallery  |  Sitemap  |  Inquiry  |  Contact Us  
 
 
 
 Mortars For Acid Proof Brick /  Tile  /  Mandana Stone  
 Acid Proof Tiles  
 Acid Proof Bricks  
 Acid Proof Lining  
 Acid Proof Flooring  
 Acid Resistant Tiles  
 Acid Resistant Bricks  
 Acid Resistant Lining  
 Acid Resistant Flooring  
 Red Mandana Stone  
 Epoxy Lining  
 Epoxy Flooring  
 Epoxy Coating  
 Water Base Epoxy  
 Glass Flake Filled Lining  
 Glass Flake Lining  
 Glass Flake Coating  
 Grouts  
 Water Proofing  
 Liquid Applied Stainless Steel  316 Coating  
 P.U.Flooring  
 Water Base Polyurethane  
 Polyurethane Wall Coating  
 Polyurethane Flooring  
 Self Leveled Epoxy Flooring  Coating Linings  
 
 
 

 

 

 

  MORTARS FOR ACID PROOF BRICK / TILE / MANDANA STONE
 
 
   
EPOXY MORTAR (HYB) :-
°
INTRODUCTION:

This HYB mortar is versatile three (3)-component chemical resistant hybrid EPOXY resin base mortar. The product exhibits excellent bond strength, high chemical resistance and reliable curing characteristics.

°
AREAS OF USE:

EPOXY HYB can be used in construction of acid resistant screed & brick/tile linings to floors, drains, sumps, tank farm areas, tanks & process vessels, waste water treatment plants etc. and jointing mortar for red Mandana stone flooring. It is the most suitable for use in installation of acid resistant brick/tile lined areas, which are very often subjected to concentrated acids and alkaline conditions.

° OUTSTANDING FEATURS:

1)Resistant to 90% Sulfuric acid conditions at room temperature.

2) Resistant to organic solvents

3)Resistant to Caustic Conditions & Hypo chlorite solutions.

4) Very low Shrinkage.

5) Excellent bond strength to acid resistant brick/tile/stone.

°
METHOD OF APPICATION MIXING:

Make sure that the contents of each container are thoroughly mixed before use.

1. Pour measured quantity (One part by wt.) of part A into clean, dry mixing container.
2. Add measured quantity of part B (0.6 part by wt.) and mix thoroughly for one minute.
3. Add measured quantity of part C filler (5.5 parts by wt.) a little at a time, mix slowly until the filler is thoroughly wetted by the resin (Part A) & Hardener (Part B) mix, to produce a homogenous trowel able mortar.
4. Mortar, which has begun to set, cannot be recovered by adding more resin. Such mortar must be discarded.
5. Never add water and any other diluents.

°
USE INSTRUCTIONS:

EPOXY HYB mortar is applied by trowel to clean, dry, neutralsurface with following procedures:
1) All bonding surface shall be buttered completely without voids.
2) Mortar joints should be kept full, and minimum 4mm wide.
3) Mortar may be applied directly over mastic membrane surface and other membrane surfaces including rubber and plastics.
4) Reducing the ration of filler in the mix shall not lengthen the working & setting time of mortar. These factors are best controlled by temperature.

°
CLEAN UP:

Mixing & application tools shouldbe cleaned radically using M.E.K., xylene or toluene. Observe proper safety precautions while cleaning.

°
CURE TIME:

If the substrate and ambient air temperature in contact with the acid resistant brick/tile construction are at 250 C allow a minimum of 24 hours cure time before putting the acid resistant brick/tile lining construction to
its intended service.

°
STORAGE & SHELF LIFE:

All the components Resin, Hardener & Filler must be kept in cool, dry place and in covered shed.

° PACKING Solution:

Resin: 25 kegs and 200 kegs Hardener 15 kegs Filler 50 kegs in LDPE+HDPE bags.

°
HEALTH & SAFETY:

It is advisable to wear protective wears at the time of use of EPOXY HYB and all other our products. In case of contact with eyes and skin, wash with plenty of water and consult a doctor. This information, given above in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use is beyond our control.
 
CHEMIPROTECT ENGINEERS
Contact at Works :-
Plot No. 2114, Phase III, G.I.D.C. Estate, Vatva,
Ahmedabad-(India) - 382445.
Call Us :- Works +91-79-25891689
Fax :- +91-79-25830002
E-mail us :- info@acidproofindia.com

chemiprotect@dataone.in

chemiprotect@gmail.com