Home  |  About Us  |  Products  |  Services  |  FAQ’s  |  Gallery  |  Sitemap  |  Inquiry  |  Contact Us  
 
 
 
 Mortars For Acid Proof Brick /  Tile  /  Mandana Stone  
 Acid Proof Tiles  
 Acid Proof Bricks  
 Acid Proof Lining  
 Acid Proof Flooring  
 Acid Resistant Tiles  
 Acid Resistant Bricks  
 Acid Resistant Lining  
 Acid Resistant Flooring  
 Red Mandana Stone  
 Epoxy Lining  
 Epoxy Flooring  
 Epoxy Coating  
 Water Base Epoxy  
 Glass Flake Filled Lining  
 Glass Flake Lining  
 Glass Flake Coating  
 Grouts  
 Water Proofing  
 Liquid Applied Stainless Steel  316 Coating  
 P.U.Flooring  
 Water Base Polyurethane  
 Polyurethane Wall Coating  
 Polyurethane Flooring  
 Self Leveled Epoxy Flooring  Coating Linings  
 
 
 

 

 

 

  MORTARS FOR ACID PROOF BRICK / TILE / MANDANA STONE
 
 
K - SILICATE MORTAR :-
°
INTRODUCTION:

This is Silicate type, two-part chemical setting mortar. It is recommended against permanently acidic condition, and can withstand much higher temperature compared to other resin type & sulfur type mortar.

°
AREA OF APPLICATION:

K-silicate is principally used with acid resisting bricks and tiles for acid resisting masonry construction,because of its very low cost. It is highly recommended to protect chimneys, incinerators and other high temperature equipment.

° PHYSICAL PROPERTIES:

Color Brown
Mix Ratio by wt. Sol to
Powder
1: 2.5
Compressive Strength kg/cm2 150
Flexural Strength kg/cm2 40
Bond Strength kg/cm2 5
Water Absorption 18%
Max. Temp. 900 C
Setting Time 8-10 Hrs.


°
METHOD OF APPICATION MIXING:

K-silicate is prepared by mixing solution & powder to form workable mortar. The recommended ratio of mixing is 1 part solution to 3 parts powder by wt. This ratio will vary depending upon ambient temperature and working conditions. Use clean dry mixing pan. Place appropriate quantity of solution in mixing Pan, and add powder slowly and start mixing thoroughly, until you get smooth paste like mortar. Do not mix more material, then, can be used within 30 minutes.

°
APPLICATION:

Mortar is buttered on acid resistance brick/tile as usual bricklayers Method. Brick/tile also should be clean,dry and at ambient temperature. After hardening of the joints, it should be treated with 10 % Hydrochloric acidbefore the acid resisting lining is place in use. During & after completion of lining, area must be kept dry and free from any other materials and traffic, which can affect setting & curing of K- silicate.

°
CHEMICAL RESISTANCE:

K-silicate when completely set hard, resistant to high concentration of oxidizing acids, inorganic acids and salts and most organic solvents at high temperature. It is not recommended against Hydrofluoric acid, fluorides, fluoride salts, water, diluted solutions, alkalis etc.

° STORAGE & SHELF LIFE:

always keep solution and powder in cool, dry place and away from direct sunlight, moisture etc. If stored in sealed container as above, shelf life of solution: 12 Months Powder: 12 Months.

° PACKING Solution:

25 kgs & 250 kgs (net) good quality MS drums. Powder: 50 kgs (net) LDPE+HDPE bags.

°
HEALTH & SAFETY:

It is advisable to wear protective wears at the time of use of K-silicate and all other our products. In case of contact with skin or eyes wash with plenty of water and consult a doctor. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without any guarantee since the conditions of use are beyond our control.
 
K Silicate, Silicate Cement, k silicate manufacturer, K silicate India
 
CHEMIPROTECT ENGINEERS
Contact at Works :-
Plot No. 2114, Phase III, G.I.D.C. Estate, Vatva,
Ahmedabad-(India) - 382445.
Call Us :- Works +91-79-25891689
Fax :- +91-79-25830002
E-mail us :- info@acidproofindia.com

chemiprotect@dataone.in

chemiprotect@gmail.com