: Water base epoxy coating is a proprietary “water-based” 2 component,
epoxy coating system that outperforms and outlasts
most solvent based sealer systems without the
associated odors, flammability, or VOC’s.
this product is available in clear and selected
- Excellent Adhesion
- Applies to Damp Concrete
- Excellent Gloss & Gloss Retention
- Good Color
- Excellent Stain Resistant
- Excellent Hardness Development
- Rapid Dry Time
- Easy Clean-up
Water base epoxy primer is the
recommended primer for most epoxy flooring systems.
It is also recommended as a stand-alone coating
Floor and wall, sealers, primers and topcoats:
Industrial maintenance, General metal &
transportation primers & topcoats.
10 Kgs., 25 Kgs & 50 Kgs Units of Part A &
| 1 year in sealed container in cool, dry
| Mixing Ratio by wt.
|| 1 part A to 2.5 parts B (1:2.5)
| Coverage 2mm th.
|| 10-12 Sq.Met. /coat
| Application Method
|| BY Brush, Roller
| Ready for Foot Traffic
|| 12+ hours
| Ready for Heavy Traffic
|| 24+ hours
COVERAGE : This product should
be applied at the rate of approx. 10-12 sq.met
per kg. As with all coatings, coverage is dependent
on the smoothness & porosity of the surface.
As a primer, the coverage rate should be 10 sq.met.
PREPARATION : The substrate must be clean,
dry and sound with new concrete cured for at least
28 days. Remove dust, laitance, grease, curing
compounds, waxes, foreign particles, disintegrated
or soft base materials, and any previously applied
coatings. Create a surface profile on concrete
by either steel shot blasting or acid etching.
Repair cracks and joints with EPOXY CRACK &
PATCH mortar. If the concrete surface is not prepared
properly, product adhesion will fail and warranties
will be voided.
FOR BEST RESULTS :
For interior use only
New Concrete must cure for 28 days
DO NOT thin MIPRO-WBE
DO NOT use when humidity Exceeds 85%
DO NOT allow material to Puddle during application
Allow each coat to Dry Tack-Free and clear
Apply Each Coat Within 24 hours of previous
Do NOT APPLY to Structurally Unsound Surfaces.
Apply a Test Patch to Ensure Adhesion to Old
MIXING: Avoid mixing and application
of this product if the surface temperature is
high and humidity is higher then 70% R.H. The
temperature of the surface, materials and air
in the area of installation all play a role in
how the product will apply and cure. Stair part
A & B separately and then pour part B in to
part A in proper ratio and blend thoroughly for
minimum for 2-3 minutes with a spiral mixing blade
attached to a low-speed electric drill. Take care
not to induce air into the material when mixing.
This will cause bubble in the coating when applied.
POT LIFE: At 30o C and 50% R.H.
the water base epoxy has a useful working time
or pot life of 25-30 minutes. Using any product
beyond this time will result in variable results
and therefore any mixed product beyond the pot
life should be discarded.
APPLICATION : The recommended
application of this product is by roller. Allow
water base epoxy coating to dry thoroughly before
mixing and applying the next coat. It should be
tack free and clear in appearance before recoating.
CLEAN-UP : Application equipment
should be cleaned using soap and water.
HEALTH & SAFETY It is advisable
to wear protective wears at the time of use of
water base epoxy and all other our products. In
case of contact with eyes and skin, wash with
plenty of water and consult a doctor.
This information, given above in good faith,
is based on results gained from experience and
tests. However, all recommendations or suggestions
are made without guarantee since the conditions
of use is beyond our control.